A B C D E F G H I J K L M N O P R S T U V W Y
 


A

AC: Alternating Current – Electrical supply in which the polarity of the hot wire reverses rapidly.

AGA: American Gas Association.

AHRI: Air-Conditioning, Heating and Refrigeration Institute.

Ambient Temperature: The average temperature of the atmosphere in the vicinity of an appliance.

Ampere: Unit of measure of current flow.

Anode Rod: A sacrificial rod composed of one or more metals installed in the water heater that protects the tank from corrosion helping extend the life of the tank.

Anti Scald Valve: Device used to prevent high water temperature.

ASHRAE: American Society of Heating Refrigeration Air Conditioning Engineers.

ASME: American Society of Mechanical Engineers.

Atmospheric Combustion: Combustion takes place when gaseous, liquid or solid fuels react at an elevated temperature with oxygen by burning, thus releasing heat in an open combustion system.

 

top of page


B

Back Flow: When water travels from one system upstream or back into any part of the main distribution system.

Boiling Point: The boiling point refers to the temperature at which a liquid changes to vapor by the addition of heat.

BTU: British Thermal Unit – Unit of heat energy required to raise 1 lb. of water 1°F.

Burner: A device in a which a flame or heat is produced in a water heater.

 

top of page


C

Check Valve: Allows fluid to flow in only one direction in a pipe; also known as back-flow preventer.

Closed System: A system where the incoming cold water supply has a device that will not allow water to expand when heated (i.e. check valve, back-flow preventer, some pressure reducing valves, water meters).

Combustion Chamber: The location where combustion takes place.

Combustion Gases: Gases released when a gaseous, liquid or solid fuel reacts at an elevated level that needs to be vented with gas or oil-fired water heaters.

Commercial Application: Demand for more water usage than in a single family dwelling.

Condensation: Excessive water vapor formed at low combustion gas temperatures.

Conventional Venting: Atmospheric venting that utilizes the natural convective rise of hot flue gases through the system to release the products of combustion.

Cycle: The number of times per second, measured in Hertz (Hz), that a conductor carrying A.C. returns to the same frequency; generally 60Hz cycle A.C. is supplied.

top of page


D

DC: Direct Current – Electrical supply in which the polarity of the two wires does not change.

Degree Rise: Difference (Delta "T") between the starting water temperature and the ending temperature after heating is complete.

Dielectric: A nonconductor of direct electric current.

Dip Tube: Tube inside the water heater that sends cold water to the bottom of the tank.

Direct Vent: Pulls outside air for combustion and vents combustion gases directly outside.

Draft Diverter: A device fitted in the flue way of a gas appliance to prevent updraft, downdraft or the secondary flue blockage from obstructing the escape of products of combustion or otherwise affecting the normal operation of the appliance.

Drain Valve: Device designed to allow drainage of stored contents from a water heater.

Dual Element Heater: An electric water heater with an upper and lower element for heating water.

top of page


E

E.C.O.: Energy Cut Off – Safety device designed to shut power off to the water heater and prevent high temperature.

EF: Energy Factor – A measure of the overall efficiency rating of the water heater based on the model’s recovery, efficiency, stand-by loss and energy input.

Efficiency: A measure of a product's ability to utilize input energy; expressed as a percentage.

Energy Guide Label: The Federal Trade Commission (FTC) requires that gas, electric and oil residential automatic storage water heaters be labeled to show 1.) an estimated annual cost of operation for that particular model, based on a national average cost of fuel specified by FTC and 2.) how the efficiency of that model compares to all other comparable models.

Expansion Tank: Designed to absorb excess pressure due to thermal expansion, e.g. closed system.

top of page


F

First Hour Rating: Combination of the usable stored volume of hot water in tank, plus the recovery capacity for the first hour of operation.

Flow Control Valve: Device designed to reduce water flow (GPM) to a plumbing fixture (i.e. shower head at 5 GPM vs. 2.5 GPM); the use of flow control valves can be cost effective in load calculations, reducing the water usage and the amount of energy used to heat water.

Flow Rate: Rating in gallons per minute (GPM) or gallons per hour (GPH).

Flue: A passage way for products of combustion.

Flue Baffle: A device to deflect, check or regulate flow of combustion gases through the flue.

Flue Damper: Minimizes convective heat loss through venting system.

Foam Insulation: The insulation surrounding the surface of the water heater tank.

Foot Print: The area of space taken up by the water heater.

FVIR: Flammable Vapor Ignition Resistant.

top of page


G

Galvanic Action: If two unlike metals are immersed in an electrolyte, an electrical potential will exist between them; if the two are in electrical contact, an electrical current will flow; the metal which becomes the anode of this cell will corrode and dissolve while the cathode will be protected from corrosion.

GAMA: Gas Appliance Manufacturers Association. Now called AHRI (Air-Conditioning, Heating and Refrigeration Institute).

Gas Control: Device used to regulate gas pressure on a water heater.

Glass Lining: See Vitraglas®.

top of page


H

Hard Water: Natural waters contain impurities in various proportions; traditionally hardness is a measure of calcium or dissolved solids in a solution. Below is a list of the types of hardness and their referenced parts per million range.

  Type of Hardness
  • Soft 0-49ppm
  • Fairly soft 50-99ppm
  • Fairly hard 100-149ppm
  • Hard 150-249ppm
  • Very hard 250 plus
Grains
  • 0 - 2.91
  • 2.92 - 5.83
  • 5.84 - 8.75
  • 8.76 - 14.59
  • 14.60+

 

Head Loss: The pressure of water as measured at a stated point; it may be measured in feet or in pounds per square inch (PSI).

Heat Exchanger: A heat transfer system.

Heat Transfer: When heat is passed from one medium to another.

Heat Trap: Restricts heat loss through water connections to a tank.

Hertz: A measure of frequency; one Hertz equals one cycle per second; 60 cycle A.C. is 60 hertz A.C.

Hydrojet®: Cold inlet tube designed to reduce sediment build-up as well as increase efficiency and overall hot water availability in the water heater.

top of page


I

Immersion: Referring to something submerged in water.

Incoming (Inlet) Temperature: Temperature of water entering tank.

Input: The amount of fuel used by a water heater in a given period of time; generally rated in one hour.

Instantaneous Water Heater: A type of water heater that heats water as it flows through a heat exchanger coil.

ISO 9000: A series of five standards for developing a total quality management system. Developed by the International Organization for Standardization based in Geneva, Switzerland.

top of page


J

Jetport: Referring to the Hydrojet dip tube. Creates turbulence in the tank.

Junction Box: Utility area where incoming power supply is connected in water heater.

 

top of page


K

KW - Kilowatt: A measure of the rate of supply of energy or power, and is equal to 1000 watts or 3412 BTU's per hour.

 

top of page


L

Laminar Flow: Streamline flow in a fluid near a solid boundary.

Life Cycle Labs: A place where water heaters are tested at an accelerated rate to simulate life expectancies.

Light Duty (LD): Small demand commercial applications.

LP: Liquid Propane – A fuel for gas water heaters.

 

top of page


M

Manifolded Installation: Parallel or reverse flow plumbing of water heaters for large hot water demand applications.

Millivolt: One thousandth of a volt.

Mixing Valve: Mixes cold water with hot water from the water heater to achieve a specified delivery temperature.

 

top of page


N

Natural Gas: A fuel delivered by a utility distribution system used on gas-fired water heaters.

Net Usable BTU: That portion of a fuel’s heat energy actually transferred into the water by the heater.

Non–CFC: Foam insulation that minimizes the use of Chlorofluorocarbons.

NSF: National Sanitation Foundation.

 

top of page


O

OHM: A unit of electrical resistance.

Oil Powered: A water heater that uses oil as its fuel source.

Operating Cost: The cost of running a water heater for a given time period.

 

top of page


P

Parallel System: Two or more identical size heaters piped with water connections, that is cold water travels equal distance into the inlets of the heaters from a "T" connection and hot water travels equal distance from the outlet of the heaters to a "T" connection.

Peak Hour Demand: Time when the largest demand for hot water is needed.

Peak Load Period: That period of the day when the system has the greatest demand.

Phase: For ease of production and distribution, A.C. is distributed in what is known a 3 phase supply using three active wires and one neutral wire.

Pilot: A small burner used to ignite the main burner.

Point Of Use Water Heater: Small water heater used for remote locations.

Power Venting: Mechanical draft exhaust to outside, usually utilizing room air to support combustion.

Preheated Water: Water that has been tempered for inlet supply to the water heater.

Pressure Reducing Valve: A valve which automatically reduces inlet water pressure to a specified value at its outlet under static cold water conditions.

 

top of page


R

Rated Storage Volume: Quantity of water (expressed in gallons) stored in a tank.

Recovery (GPH): The amount of water in gallons that can be heated in one hour.

Residential: Water heaters for single family dwellings.

Return Circulation System: Tempered water from or near the point of usage which eliminates waste of hot water used for long runs and adds storage to the system.

Reverse Flow: Another method of manifolding water heaters together in order to limit the unbalanced pressures in a multiple heater installation.

RF: Recovery Factor – Rating based on the efficiency of the product which is input required to raise 1 gallon of water 1°F.

 
  • Gas – 75% to 99% RF = 11 to 7.9 BTU/H
  • Electric – 100% RF = .0024 KW/H
  • Oil – 70% to 85% RF = 11.79 to 9.7 BTU/H

 

top of page


S

Safety Shut Off Valve: A device on a gas appliance which shuts off the gas supply to prevent a hazardous situation. A flame failure safety shut off operates when the actuating flame becomes extinguished. A 100% shut off cuts off all gas including main and pilot burners.

Scale: A coating or layer (usually lime, biocarbonate or calcium) on the bottom of a tank or interior parts, that may prevent heat transfer.

Sealed Combustion: Sealing of combustion chamber to prevent spillage of combustion products.

Sediment: The substance that settles on the bottom of a tank.

Series System: Generally where the primary heater preheats water to a given desired general purpose temperature and feeds into another heater.

Sight Hole: Generally referring to oil-powered product that allows the viewing of burner and flame patterns.

Sliding Inner Door: A door slides along combustion chamber radius for easy access to the burner and pilot.

Solenoid: A coil of wire in the form of a cylinder that carries a current; resembles a bar magnet.

Spark Ignition: Intermittent ignition device that utilizes a spark to light a burner flame.

Spark Test: A test procedure to evaluate the integrity of the glass lining.

Spud: A threaded opening on the water heater tank.

Stacking: Also known as thermal stratification, or build-up, it is the ability of hot water to form layers of different temperatures in the tank.

Stand By Loss: The amount of heat lost while unit is in stand by mode.

Standing Pilot: A small burner used to ignite the main burner.

Storage Tank: A tank used to hold a specific volume of water.

Surface Mount: Usually referring to thermostats mounted on the outside of the tank surface which senses temperature through the steel tank.

 

top of page


T

T & P Valve: Temperature & Pressure Relief Valve.
A safety device used to expel excess pressure or temperature from inside a tank.

Tankless Water Heater: Commonly known as instantaneous or point-of-use water heaters.

Temperature Rise: (Delta "T") The number of degrees Fahrenheit (F) the incoming cold water must be raised to reach the desired hot water temperature.

Therm: A measurement of 100,000 BTU’s.

Thermal Efficiency: Ability to transfer and absorb heat from fuel source into the water.

Thermal Expansion: Water, a non-compressible liquid, expands when heated.

Thermal Stratification: Also known as stacking, or build-up, it is the ability of hot water to form layers of different temperatures in the tank.

Thermocouple: A small electric generator. Electron flow between the hot junction (where pilot flame envelopes the thermocouple) and the cold junction (where the capillary meets the bottom of the thermocouple) creates millivoltage.

Thermopile: An apparatus that consists of a number of thermocouples combined to multiply the effect and is used for generating electric current.

Thermostat: A device which automatically maintains a predetermined temperature in an electric water heater. Most thermostats are equipped with a safety shut-off.

Turbulent Flow: A fluid flow in which the velocity at a given point varies erratically in magnitude and direction.

 

top of page


U

UL: Underwriters Laboratories.

Usable Storage: The percentage of hot water that can be drawn from a tank before the temperature drops to a point that is no longer considered hot.

 

top of page


V

Vacuum Relief Valve (Anti-Siphon): Recommended for installation on all side (bottom) cold inlet heaters; prevents internal vacuum conditions that could drain a system by back siphonage, eliminates burned out electric elements and collapsed tanks.

Venting Materials: Materials used for evacuating vent gases from a dwelling.
i.e. PVC, CPVC, ABS, metal

Vitraglas®: Bradford White water heater tanks are protected from the corrosive effects of hot water by an exclusive ceramic porcelain enamel coating. The Bradford White high silica Vitraglas(R) lining provides a tough interior surface for our water heater tanks.

Volt: Unit of measurement of electromotive force. AC or DC

 

top of page


W

Waterway Fitting: A channel through which water can flow; connects water heater to inlet & outlet lines.

Water Hammer: A concussion or sound of concussion of moving water against the side of a containing pipe or vessel.

Watt: A unit of electrical energy or power; one ampere x one volt = one watt.

Watt Density: Amount of watts concentrated per square inch of element rod surface area.

Working Pressure: Maximum pressure of the operating system permissible.

 

top of page


Y

Yearly Cost: The cost of operating a water heater for a year.

 

 

 

A-C | D-G | H-K | L | M | O-P | R-S | T-X

 


A - C

Aero Series: Product series within BWC line containing oil-powered product, air handlers, oil burners and gas power burners.

Air Handlers: Fan coil heating units that connect to hot water source (i.e. water heater) and utilize that heat to create warm air for space heating or fresh air make up.

ASME Immersion Thermostat: Refers to standard duty commercial electric water heater built to A.S.M.E. code construction specifications and where temperature sensor is inside integral storage tank.

AST (Aero) (AKA Storage tank): Hot water storage tank used in conjunction with a boiler or fuel fired water heater.

Boiler: Gas or oil fueled appliance without storage tank that heats water via heat exchanger for whole house or building space heating.

Booster: Refers to under-counter style or point of use water heater used in commercial dishwashing applications.

Center Flue: Refers to Flue configuration in center of oil-powered water heater (Aero Series)

CombiCor: First generation dedicated combination space and water heating product with internal heat exchanger coil. Can be oil or gas-powered.

Combination Heating: Refers to products designed to heat both water and living space.

Commercial: Refers to products with output sufficient for industrial or business use.

Copper Brute I & II: Refers to multiple types of commercial gas powered water heaters that can supply maximum demand and are used in conjunction with a large volume commercial storage tank. Models for both indoor and outdoor installation.


top of page

D - G

Dairy Barn: Refers to electric water heater with high ground clearance for use in dairy industry.

Defender: BWC name for FVIR compliant combustion chamber (Defender Safety System).

Direct Vent: Refers to water heaters that utilize dual pipe venting system for combustion air and exhaust.

Double Wall: Refers to the internal heat exchange coil in an indirect water heater as two layers of glass-lined steel.

eF Series: Standard duty commercial gas water heater with unbalanced, directventing and efficiencies as high as 99.1%.

Electric Brute: Refers to high demand commercial electric water heaters used in conjunction with a large volume commercial storage tank. Includes Vertical Round, Vertical Square and Horizontal Square configurations.

Electric-powered: Refers to Products that use electricity as fuel.

Energy Saver: residential and commercial water heater classification.

Energy Saver – Electronic Ignition: Standard duty commercial gas water heater with electronic ignition.

Energy Saver – Millivolt: Standard duty commercial gas water heater with millivolt controls.

EverHot: Bradford White name for tankless, continuous flow water heater line.

Gas-powered: Refers to Products that use either natural or propane gas as fuel.


top of page

H - K

High Input Direct Vent: Refers to water heaters that utilize a dual pipe venting system for combustion air and exhaust and recover more hot water faster than standard models.

Hydronic Heating: Refers to the use of heated water to heat living space (i.e. baseboard, in-floor radiant applications).

Immersion Thermostat: Refers to standard duty commercial electric water heater where temperature sensor is inside integral storage tank.

Indirect-powered: Refers to products used in conjunction with a boiler or other hot water source to heat water in a storage tank via an internal heat exchange coil.

KwickShot: Point of use electric instantaneous water heater.


top of page

L

Large Volume Jacketed: Refers to storage tank that is insulated and has outer sheet metal shell. Used with water heater in standard commercial applications.

Large Volume Unjacketed: Refers to storage tank that is un-insulated (bare) and has no outer shell. Used with water heater in standard commercial applications.

LD DV: Refers to water heaters that utilize dual pipe venting system for combustion air and exhaust for use in smaller commercial applications.

LD Jacketed: Refers to storage tank that is insulated and has outer sheet metal shell. Used with water heater in smaller commercial applications.

LD Lowboy: Style of electric water heater for use in smaller commercial applications with cylindrical shape and reduced height for low ceiling/confined spaces.


LD PDV: Refers to water heaters with power blower that utilizes a dual pipe venting system for combustion air and exhaust for smaller commercial applications.

LD TTW: Refers to water heater that uses a powered blower to vent combustion gases through outside wall or roof in smaller commercial applications.

LD Upright: Traditional style of electric water heater with cylindrical shape for use in smaller commercial applications.

LD Utility: Style of electric water heater with varying storage capacity for smaller, point of use, commercial applications.

LD Wall Hung: Style of electric water heater designed for wall mounting with bottom inlet and outlet connections for use in smaller commercial applications.

Light Duty (LD) Energy Saver: Refers to conventional vent water heater for smaller commercial applications.

Lowboy: Style of electric water heater with cylindrical shape and reduced height for low ceiling/confined spaces.


top of page

M

M1: Denotes standard model, gas-powered residential water heater.

M4: Refers to gas-powered models that meet C.E.C. Title 24, South Coast Air Quality Management District and all other district requirements.

Manufactured Home – Atmospheric Combustion: Refers to water heaters for use in mobile homes that utilize conventional combustion and venting.

Manufactured Home – Closed Combustion/Direct Vent: Refers to water heaters for use in mobile homes that utilize a single vent configuration that provides both intake air and exhaust venting.

MD 3-Element: Medium duty electric water heater with three heating elements for use in large residential or smaller commercial applications.

Multi-Flue: Refers to multiple Flue configuration for enhanced heat transfer in commercial oil-powered water heater.


top of page

O - P

Oil Burners: Combustion apparatus utilizing fuel oil to generate heat/hot water (Aero Series).

Oil-powered: Refers to products that use oil for fuel.

PDV with Independent Venting: Standard duty commercial gas water heater with powered direct venting that utilizes external combustion air and exhaust through outside wall via separate vent and intake pipes.

Pool Heater: Heater designed to heat water in a residential swimming pool (Aero Series).

Power Burners: High input combustion apparatus utilizing natural gas to generate heat/hot water in power burner water heaters.

Power Burner Water Heaters: Large volume commercial gas water heaters with gallon capacities up to 1,500 gallons. For use in hotels, hospitals, stadiums, etc.

Powerful Compact (PC): Point of use electric water heater featuring 2 gallon storage capacity.

Power Direct Vent (PDV): Refers to water heaters with power blower that utilizes dual pipe venting system for combustion air and exhaust.

PowerStor DW: Indirect-powered (or fired) water heater with double wall glass-lined steel heat exchanger coil.

PowerStor SS: Indirect-powered (or fired) water heater with stainless steel single wall heat exchanger coil and tank.

PowerStor SW: Indirect-powered (or fired) water heater with single wall glass-lined steel heat exchanger coil.


top of page

R - S

Rear Flue: Refers to Flue configuration at rear of oil-powered water heater (Aero Series)

Residential: Refers to products with output sufficient for in-home/consumer use.

Side Connects: Refers to water heaters with tappings or holes in side of storage tank for use in hydronic heating applications.

Single Wall: Refers to the internal heat exchange coil in an indirect water heater as one layer of glass-lined steel.

Solar Saver: Water heater used in conjunction with solar heating equipment. Includes electric element back up.

Space Heating: Refers to products designed to heat living space.

Storage: Refers to water heaters with integral tank to hold heated water.

Surface Mount Thermostat: Refers to standard duty commercial electric water heater where temperature sensor is mounted on outside of integral storage tank.


top of page

T - X

Tabletop1: Style of electric water heater for use in kitchen with integral countertop1.

Tankless: Refers to products with no storage capacity that utilize a heat exchanger or burner system to heat water as it passes through tubular heat exchanger.

TTW1(Through-the-Wall): First generation product that uses a powered blower to vent combustion gases through outside wall or roof.

TTW2 (Through-the-Wall): Second generation product with higher BTU inputs that uses a powered blower to vent combustion gases through outside wall or roof.

Upright: Traditional style of water heater with cylindrical shape.

Upright HE: Refers to electric water heater with higher efficiency ratings than standard upright electric models.

Utility: Style of electric water heater with varying storage capacity for point of use applications.

Water Heating: Refers to products designed to heat water.

Wall Hung: Style of electric water heater designed for wall mounting with bottom inlet and outlet connections.

XR: Extra Recovery - Refers to gas-powered models that recover more hot water faster than standard models.